Sign in to follow this  
Peter Brands

Scratch Build : L3p D3sk - Small update :P 15-7

Recommended Posts

Been playing with a lot of stuff this weekend ;)

Testing with the 2 (3) PSU's

Total of 2600W running now.

And off course my 3.3V 5V and 12V are superb now :)

Very silent psu's by the way !

P1060134%20%5B550x%5D.JPG

Even under full stress :)

980x @ 4.5 Ghz + 2 x GTX580 @ 960/1150

P1060136%20%5B550x%5D.JPG

And creativity with Bitspower on a Sunday afternoon :D

It was to see the effect of flowing Acid green right under UV leds in the desk.

(For further plans ;) )

P1060146%20%5B550x%5D.JPG

Share this post


Link to post
Share on other sites

Needed for the Coolermaster PSU's

P1060168%20%5B550x%5D.JPG

After the mouse i was looking for a fitting mousepad for the desk.

Personally i like cloth pads like the Q-pad.

Couldn't find anything at all.

All i could find was a pad with leds in it.

But then the idea popped up ..

Still had some plexi somewhere, and there are 150 UV smd leds in my desk so why not try it :P

The plex.

(Fits perfectly !)

P1060169%20%5B550x%5D.JPG

The "hard" SLI connector.

P1060170%20%5B550x%5D.JPG

And my RVS cupholder :)

P1060171%20%5B550x%5D.JPG

P1060172%20%5B550x%5D.JPG

With a jigsaw.

P1060177%20%5B550x%5D.JPG

Maybe im going to let the print melt down into the plexi with its pins

P1060182%20%5B550x%5D.JPG

The Q-Plex :)

P1060184%20%5B550x%5D.JPG

P1060185%20%5B550x%5D.JPG

And the ...ehm ..cupholder :)

P1060186%20%5B550x%5D.JPG

Still goin to polish them some more later.

P1060187%20%5B550x%5D.JPG

Share this post


Link to post
Share on other sites

I could sell my Intel X18-M for a good price, so wanted to try the Intel 510.

Going to use it as OS drive

P1060217%20%5B550x%5D.JPG

P1060218%20%5B550x%5D.JPG

P1060221%20%5B550x%5D.JPG

Intelbench%20%5B550x%5D.jpg

Last pieces of work for the SLI connector :)

P1060211%20%5B550x%5D.JPG

P1060224%20%5B550x%5D.JPG

P1060226%20%5B550x%5D.JPG

P1060228%20%5B550x%5D.JPG

P1060231%20%5B550x%5D.JPG

Share this post


Link to post
Share on other sites

Still had to change some things under my floor.

Today i found some time.

Had to replace some fans on my rad for Scythe GT's

Replaced the green tube for Tygon black.

Also replaced the 3 remaining GT's in my desk for green Nanoxia's

P1060254%20%5B550x%5D.JPG

GT's out

P1060255%20%5B550x%5D.JPG

Only 5cm space for my hand.

P1060256%20%5B550x%5D.JPG

Nanoxia's in.

P1060257%20%5B550x%5D.JPG

Here my radiator in the distance.

P1060262%20%5B550x%5D.JPG

On request also made a little movie of my trip :)

Mobile doesn't work here, but baby phone works fine :D

P1060263%20%5B550x%5D.JPG

De GT's on their place and tubes replaced !

P1060267%20%5B550x%5D.JPG

P1060268%20%5B550x%5D.JPG

P1060273%20%5B550x%5D.JPG

And another small test.

Wanted to know what stuff goes trough my loop.

This way it was easy to discover.

P1060279%20%5B550x%5D.JPG

Click it between my tubes and enable the pumps for one hour.

P1060305%20%5B550x%5D.JPG

Then disconnect the filter while pumping and stop the pumps as fast as you can.

This is so the dirt really stays in the filter.

P1060307%20%5B550x%5D.JPG

All tiny hairs and wtf, even a piece of my sigarettes :P

P1060313%20%5B550x%5D.JPG

Till next time :P

Share this post


Link to post
Share on other sites

Received a nice UV led board today.

It's specially for making photo's from UV-active parts.

You can only use it for 5 minutes per time, else it gets too hot :)

P1060362%20%5B550x%5D.JPG

P1060363%20%5B550x%5D.JPG

Small surprise between the UV leds :)

P1060364%20%5B550x%5D.JPG

And some pictures with the effect

P1060374%20%5B550x%5D.JPG

P1060380%20%5B550x%5D.JPG

P1060386%20%5B550x%5D.JPG

P1060399%20%5B550x%5D.JPG

P1060401%20%5B550x%5D.JPG

P1060402%20%5B550x%5D.JPG

P1060405%20%5B550x%5D.JPG

P1060406%20%5B550x%5D.JPG

Share this post


Link to post
Share on other sites

The date for powder-coating the desk has set !

Next week Tuesday ill bring it over there :P

10 minutes before unplugging it

P1060608%20%5B550x%5D.JPG

And 3 hours later :)

P1060616%20%5B550x%5D.JPG

Also took me half an hour to think how i will place the second PSU.

Decided to place them like this, ill creata another 120mm fanhole between the psu's tomorrow

P1060620%20%5B550x%5D.JPG

Wanted to use these for my quick connectors outside the desk

P1060420%20%5B550x%5D.JPG

P1060423%20%5B550x%5D.JPG

Maybe till tomorrow :P

Share this post


Link to post
Share on other sites

Yesterday the idea came up for hiding my cables from the 3 screens.

P1060621%20%5B550x%5D.JPG

Some won't like it, but for me this works great since my pc is more open then closed :P

So this way it's very easy to take away the backplates.

P1060623%20%5B550x%5D.JPG

It's only connected with the left side of the panel.

P1060627%20%5B550x%5D.JPG

2 hours later it was really empty, looks like a reverse buildlog :(

P1060628%20%5B550x%5D.JPG

Sanding it some.

P1060629%20%5B550x%5D.JPG

P1060630%20%5B550x%5D.JPG

Like a bomb exploded.

P1060631%20%5B550x%5D.JPG

Here i was finished for today :)

P1060634%20%5B550x%5D.JPG

Share this post


Link to post
Share on other sites
Robertwhamm    0

WOW... If I had a dollar for every time you took this thing apart and re-assembled it, I would almost have enough money to buy half the components you have put in there :shock: !

You have amazing patience and your build is also amazing!

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this