• Announcements

    • CM Nick

      AM4 Socket Support   04/24/2017

      Due to technical issues, the topic on "AM4 Socket Support" has disappeared. We apologize for any inconvenience this has caused and we are trying our best to have this topic back up as soon as possible.   As we read in the topic, there is a lot of discussion going on when the new brackets will be arriving. We can tell you now that the brackets will be ready for pre-order on our CM Store EU tomorrow and will be ready for shipment around the 16th of May.   You can continue the discussion in this newly created topic:     
Calen Saddler

SyNAPSE Case Mod by Envious Mods (Cooler Master 5t)

5 posts in this topic

Posted (edited)

174b2a840f2a6e1f1b695e0ab1f000cf.jpg

The Concept:

Addition To The Design: How It Came To be

I came up with this idea a while back but didn't know how or when I would implement it. As time passed the idea went into my book along with all my other crazy ideas. After looking at some Be Quiet products on their site I came across the Silent Base 800. The bottom “skids” or feet were perfect! Exactly what I had been looking for. After exploring the idea further and taking some more looks at the Cooler Master MasterCase 5t; I realized it was the perfect candidate. 

My idea was to make it look like the MasterCase 5t and the Cosmos had a love child and named it, “SyNAPSE.” it couldn't have come together any better. Combining those designs cues with the ones found on the hardware and I have a complete build that is something I would want to own but doesn't exist. It will be an uphill challenge as mounting brackets will have to be custom made and more than likely 3D printed. Less than a week ago I saw the Cosmos 700 prototype and they ventured from the round skids or feet for ones that were more like the ones I will be using. This made the SyNAPSE build even better.

Behind SyNAPSE:

I've named this build SyNAPSE as it will bridge the gap between organic and mechanical. Sharing a lot of design styling from Gundam and other off shoots. The SyNAPSE case mod will be heavily inspired by Gundam. All of the popular movies and games we see on a daily basis were born from the original, "Mobile Suit Gundam." This dates back to the early 70s and has been a mainstay in Asia ever since. Gundam consists of the futuristic mech robots that have been adapted into a lot of different platforms. It has evolved into an extremely popular line of games, tv shows and movies.

I want to go back to the roots of Gundam and adapt it to current day perspectives while focusing on the designs found throughout the hardware being used in the build. The combination will make this build one of the most cohesive builds I've ever done. Every detail from the hardware will be carried over into the rest of the build. 


a051932b2fc41ba6e3a3f73990b8fb3e.jpg

5abfb90b18562be4cbe1f5bcaac57faf.jpg

672bbf1586fd368578f11f382b79aa6f.jpg

bdb43ef92590c6b73a71a185c9062eeb.jpg


089de540482c4979b835d083746327f9.jpg

c7f7da5a5aabba73d0035ebb86a3903f.jpg


c75e1ef505cfe9058581c6ae53a2180a.jpg

CPU: Intel Kaby Lake i7 7700k
Motherboard: Aorus Z270X-Gaming 9 
GPUs: SLI Aorus GTX 1070 X 2
SLI Bridge: Aorus RGB
Memory: HyperX Savage DDR4 16gb 
Storage: HyperX Predator M.2 - HyperX Savage SSD 
PSU: Be Quiet Dark Power Pro 11 (1,000 watt) 
Cables: Modular custom sleeved CableMod cables (red, black & silver)
Fans: Be Quiet Silent Wings 3 (high speed) 3 X 120mm


7a6ed872034b35922205b4bda0cf977f.jpg

CPU Block: Alphacool Eisblock XPX (clear)
GPU Blocks: (TBD)
Pump: (TBD)
Radiators: (TBD)
Reservoir: (TBD)
SLI connector: (TBD)
Tubing: (TBD)
Coolant: Mayhems 
Fittings: Alphacool 
Flow Meter: (TBD)


3b21357d59c964a200e72926be6ca240.jpg

PWM Cables: (TBD)
LEDs: (TBD)
Top & Bottom Feet: Be Quiet Silent Base 800
Other Cables: CableMod sleeved PSU cable, ethernet cable, SATA cables and others
Thumbscrews: CableMod anodized (red)
LED Strips: CableMod RGB/W dual wide angle LEDs that work with Gigabytes RGB Fusion controllers.


31b3b27abdc98676967d008432e6c2d4.jpg

tONIYcxLf1OnASGUYWFR1-k5F7eKYM4zO0drZL7OsH4UD_H-WjNu7b-BJ1nzPwUcxW6S11cP9Qn_VqvUE0sA49u44Am3XanND4Z3DxZFtdM_zk16aj-p18qS4_OLkb0X9ylfTaFL

 

8e6874fea011e1b056118c566dd2327d.jpg

 

7997bcd57372ece0a63eb3a1559cfd73.jpg

 

c6b0239344c5c649542067cb4bf34be1.jpg

 

c34a57fd27baf6fd8893e572ba2d01a0.jpg

 

c32f455735e977f0a8af3efcccd7b0a0.jpg

 

179543c2b9fe1c02bf1dc987b9b34c94.jpg

 

0682bee678f51628b8c2d6b16443aefd.jpg

 

IMG_20170616_124639_665.thumb.jpg.1c7b27d03526ca6acf45b23e132a9d89.jpg

 

IMG_20170703_225352_748.thumb.jpg.fa0d54ad6ef719b45a52d8b24caad30b.jpg

 

IMG_20170616_221102_989.thumb.jpg.400d4bca4a49b2a2df581ce95c36c2c1.jpg

 

IMG_20170626_143925_078.thumb.jpg.d986df005e00cb11fe7a62b4e0a848e1.jpg

Edited by Calen Saddler
0

Share this post


Link to post
Share on other sites

c971c21093dc1944866058879a51a479.jpg

 

Making Templates:

 

The concept art shows the basic path I will be taking with this build. I've since added a few features that will really take this build to the next level. I started out by taking some of the designs done in the concept art CAD design and made a full scale mock up templates. This helps assure everything will fit as intended. Usually I use hard stock paper as many of you may know. This time I wanted something a little more rigid so I bought some trifold boards from the dollar store. It's a type of cardboard but different then the type of cardboard you may be used to. It works great for mocking up shrouds. I decided to make the full shroud in 3 separate pieces. Breaking the shroud up helps with installation and future maintenance. The top horizontal piece will be mounted a lot closer to the side of the case which will give it a lot more depth.

 

c12c144a0fd20cb829d5a4379619aa85.jpg

0

Share this post


Link to post
Share on other sites
e714ec5da9b43fe49946af9d77e7e25b.jpg
 
Cutting & Mocking Up Skids (top):
 
It took a lot of measurements and head scratching to figure out how I would mount the top and bottom ones. I decided to take the most challenging one 1st which was the top set. Luckily the two pieces where the skids would mount are at the same angle which made the task a but easier. Now that I have them mocked up, I can fine tune the angle that they come out of the case at. I haven't decided if I want them perfectly flat facing upwards or at a slight angle. I will more than likely wait until the bottom set is on so that I can see it both ways.
 
dfdfa6769b4771ed8dc200df717249f4.jpg
 
8737f1914324a9c9ed46b38664488a38.jpg
 
b744d9de0af87b974cd6e1ea329265e3.jpg
0

Share this post


Link to post
Share on other sites

62b1eff6908135a97383f53131b5fe60.jpg

Mocking up Skids (bottom):

Now that I have the top all mocked up I can do the bottom set. I used the measurements from the top to locate where I should mount the bottom set which assures they will match up. I had to remove both of the stock feet from the MasterCase 5t. They come out really easily after removing a couple bolts and unlock by sliding them. I've been debating on modifying the stock feet so that they can be remounted with the new skids. I will probably wait until I have the skids exactly how I want them before playing around with them. As you can see the bottom skids fit perfectly. There's a decent amount of work into getting them in but it's already paying off.

4f737a8733d36fb7d5e4d701678daa91.jpg


Top Aorus Logo:
I knew pretty early on that one wanted to put the Aorus logo in a couple spots on the outside of the case. The one I knew for sure was on the flap towards the back of the case. A buddy of mine was already laser cutting some stuff and offered to cut me a couple Aorus logos if I did the design for it. They turned out perfect. I will more than likely paint it white before mounting it so that it matches the concept art design. Here's what the Aorus Eagle looked like after being cut and mocked up. I also got a chance to paint them white. Below I show the progress of making the acrylic mount for it as well

662677b7aa50476165f5d4fd3a40d20c.jpg

57f9fb2ff29ebf44267931d46669e65a.jpg

9c611dee5b34eb9376104477c2d3e022.jpg

354b53714bb1a7236a4dd1085d020cf7.jpg


Turning Templates Into Parts:
The next task on the agenda is taking all of the templates made and turning them into actual parts for the build. Getting to this stage takes a little bit of work but once you're there goes along pretty easily. I use the templates to trace out cut paths in either acrylics or different metals depending on the use. For this side pieces I will use a combination of both for different reasons. These panels will all be at different angles and mounted in different positions. Typically I'm out most the stuff in one plain we're on this build they will be mounted in all different planes and positions. This will give it a lot more depth as it will be three dimensional versus flat surfaces.

195f5aa0e23d86f50e789166af6a8dea.jpg

0

Share this post


Link to post
Share on other sites

e59d4d8a9f9c9d9c5f25dd86c0eb9835.jpg

Painting New Panels:

Painting panels is pretty straightforward for the most part. Everybody seems to have their own way of doing things that works best for them. For these pieces I first started by lightly sanding or roughing them up so that the primer will stick to it better. With the acrylic primer is very important. The reason it is so important is the LED lighting inside the case will show through the clear panels even after they're painted, without the use of primer. So it's important to get a good thick base of primer before your color coat goes on. Doing so will help ensure that you get no bleed through from the LED lighting. For right now I will just leave them in primer which will allow me to wait until I'm done with the rough work.

e72fb96bb454adc05982849a3cee8111.jpg


Mocking Up & Testing Hardware:

I recently got a Be Quiet 240mm AIO so that I can test all the hardware and configure everything at the start of the build vs when it's finished. This had dome big advantages. It allows me to make sure there's no issues with the hardware and design the build with the configurable leds in mind. I had to also install an OS so that I can configure the fans as well. I will be using a combination of ring plus and Silent Wings 3 fans. The Ring Fans will give me some of the aesthetic look I'm going for while the Silent Wings 3s will do the intake and exhaust work. The Aorus motherboard, graphics cards and SLI Bridge are all configurable and offer multi-zone lighting. This allows me to controller everything through the motherboard and set different leds up in different ways. The ring fans have their own app and can be controlled by my cell phone. 

9a27155632b9adc318d79c002e12eb43.jpg

feb61a290c1d350b3b3666f519bb0e46.jpg

 

0

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!


Register a new account

Sign in

Already have an account? Sign in here.


Sign In Now