Recommended Posts

capten    6

Project „SL5T“



"SL" as you already know from Mercedes Benz, is to make the first impression what this project stands for. Elegance, luxury and simple forms.

The MasterCase Maker 5T is used.
The interior is as discreetly as possible cleared of all unnecessary elements.
The walls are clad with Plexiglas and multi-layered in the design of the mainboard.
An elaborate water cooling system is installed which, however, is kept as minimal as possible.
A cover is made for the cable area, which provides a window for the PSU and on which the ASROCK logo is placed in case size.
The logo is framed with the design of the X99 Gaming I7 as well as I would like the elements of the mainboard to continue the whole case. (The red racing arrows between the lower two PCIe slots)
All cables are sleevedin the hardware colors.
From the outside the contours of the Maker 5T are emphasized by Plexiglas, where also sponsor logos will be found.

So much for the formal part.
The Maker5t will be my next Rig, since I have not yet a good portable Gaming PC.
So I have now also evasive possibilities when my table times problems and above all I can finally also times my table new hardware miss.

Actually, I wanted in this project not so much effort to operate but again will grow the mod again tremendous.

Since I now the first time on a separate X99 board change, I dedicate this mod to the

ASROCK X99 Gaming I7

And let the whole project be inspired by the mainboard.

Hardware

CPU: Intel Core I7 6850K
Mainboard: Asrock Fatal1ty X99 Professional Gaming I7
Ram: Avexir Blitz 4x4Gb 2800Mhz
SSD: Avexir S100 240Gb
GPU: Nvidea Geforce GTX970
PSU:MasterWatt Maker 1200
Case:MasterCase Maker5t

Watercooling

Bitspower NGTX970MGV2 Acrylic (Clear) BP-WBVGNGTX970MGV2NPAC
Bitspower Leviathan Xtreme 240 4xG1/4" Radiator BP-NLX240-F4PB
Bitspower Leviathan Slim 280 4xG1/4" Radiator BP-NLS280-F4PB
Bitspower DDC Plus Pump BP-DDCPLS
Bitspower DDC TOP Water Tank Integrated Kit 300 (POM Version With Z-CAP II) BP-DDCTOPWTIK300PC3-BKCL
Z-Tube 250( ICE Red) BP-WTZACT250-IRD
Bitspower DDC Pump Cooler Bracket (Red) BP-DDCPCBT-RD
Bitspower Pump Cooler For DDC/MCP355 (Red) BP-DDCPC-RD
Bitspower CPU Block Summit EF (Intel) (Acrylic Top Version) BP-WBCPUIAC-CUMBKWH
Bitspower CPU Block Plate For Intel CPU (Deep Red) BP-CPUIPT-DRD
Bitspower G1/4" Deluxe White Enhance Multi-Link For OD 12MM BP-DWEML
Bitspower G1/4" Deep Blood Red Enhance Multi-Link For OD 12MM BP-DBREML
Bitspower Deep Blood Red Enhance Rotary G1/4" 90-Degree Multi-Link Adapter BP-DBRE90RML
Bitspower Deep Blood Red Enhance 90-Degree Dual Multi-Link Adapter BP-DBRE90DML
Bitspower Deluxe White Enhance Rotary G1/4" 90-Degree Multi-Link Adapter BP-DWE90RML
Bitspower Deluxe White Enhance 90-Degree Dual Multi-Link Adapter BP-DWE90DML
G1/4" Deluxe White Rotary 90-Degree IG1/4" Extender BP-DW90R
G1/4" Deluxe White Mini Dual G1/4" Extender BP-DWWP-C42
G1/4" Deluxe White Rotary G1/4" Extender BP-DWRG
G1/4" Deluxe White Muti-Transfer Adapter BP-DWWP-C03
G1/4" Deluxe White IG1/4" Extender-15MM BP-DWWP-C60
Deluxe White Mini Valve With Black Handle BP-MVV-DWBK
Deluxe White Q Plus-Block BP-DWFMB
G1/4" Deluxe White Stop Fitting BP-DWWP-C06
Bitspower None Chamfer Brass Hard Tubing OD12MM Deep Red - Length 300 MM BP-NCBHT12DRD-L300
G1/4" Deluxe White Aqua-Pipe I BP-DWWP-C17
G1/4" Deep Blood Red CaseTop Water-Fill SET BP-DBRWP-C04
X-Station Mini Power-Extension I Female Version BP-MINIXSP1F-RD
Bitspower Logo Aluminum Thumb Screw For 632 (Deep Red BP-LATSC632-DRD
Bitspower Logo Aluminum Thumb Screw For 632 (White) BP-LATSC632-WH
Bitspower Metal Tubing Cutter BP-CMMTC
Bitspower Flow Indicator BP-FI-CLBKWH
Red Blade For Bitspower Flow Indicator BP-BFI-RD
Control: Aquacomputer Aquaero 6 XT

equipment

Fan:2 x NB eLoop B12-1 ,3 x NB eLoop B14-1
Headphone:MasterPulse
Keyboard:MasterKeys Pro M


Sketches

In order to bring the project as smoothly as possible, I took this time a bit more time on the computer and already times sketches for the different covers created.
The elements are glued together in several different colors.
Partially varnished, partially foil and partly (only) polished.
For use comes Plexiglas in various colors and thicknesses, aluminum foils and varnishes.

This is only the rough basic idea, should expect again but not look good I let myself think of something else: thumbup:

This cover comes on the right side in the case inside where the drive bays sit.
To the right the original pattern and to the left the lighting effect.

coverrechts5is85.jpg

Here the front, whether the red arrows will really work well, we will see

front8zso0.jpg

Here the front of the PSU cover, the design on the left will frame the window to the PSU

psucoversfszd.jpg

And here the elements for the Windows, not completely in red but as template it is enough

windows47snm.jpg

Hardware pic´s

The majority of all components are already there, but see for yourself:


img_1848amdsag.jpg

img_1823dus9h.jpg

img_2352ghs9u.jpg

img_2394vbsoy.jpg

img_2200xosce.jpg

img_19350nswn.jpg

img_1911xos13.jpg

img_1896amstq.jpg

img_23866jsw4.jpg

img_2390ccsd3.jpg


A big thanks goes to all who support me with this project:

ASROCK

COOLERMASTER

BitsPower

Blacknoise

Avexir

Edited by capten

Share this post


Link to post
Share on other sites
capten    6
Hi!
 
After the case was made naked, I had to realize that my radiator constellation was not as fit as I wanted.
 
img_24431ya74.jpg
 
After a long time, I had to saw.
The 280er does not fit above and the 240er comes extremely far down then the piping then the mainboard would cover, so the 280er upwards.
The yellow taped points I will cut first.
The second marking is for the 8Pin Atx cable which is exactly centered with the Gaming I7. Sloping cable routing is not my thing, so I will enlarge the cable lead.
 
img_2675ojl79.jpg
 
In order to work there clean, I had to remove only the rear handle from the case.
 
img_267687bqv.jpg
 
And then everything clean, in the taped condition, cut open
 
 img_26800xbki.jpg
 
img_26812wla8.jpg
 
With the radiator bracket I had only the rear wall cut off
 
img_2682cjy00.jpg
 
img_2683lwa9o.jpg
 
The ATX cable bushing I cut up well on the double size and of course, once slipped off and the paint damaged.
Since I have already tried massively in different colors it meets this here with best but wanted to use and I will not continue it.
 
img_268407lky.jpg
 
img_26875sl29.jpg
 
Then I riveted the handle from the case immediately and the rivets painted black (right), all interfaces of course also ..
 
img_268813lzd.jpg
 
img_2689r6yvh.jpg
 
img_269020zbn.jpg
 
Then I once cut all possible materials, cut patterns created, plotted and transferred to the material.

0,75 Alu for the Midtray
2mm Plexi for the HDD Cover Designs
3mm plexiglass red fluorescent as base plate for HDD cover and The X99 Arock arrows for the Windows.
 
img_2693kixnp.jpg
 
Now it was also starting with the sawing, first the 2mm Plexiglas
 
img_2700ifxk3.jpg
 
Then the aluminum sheet
 
img_27365lzyj.jpg
 
img_27377mzuk.jpg
 
And the Decals for the Windows
 
img_2741cmxl7.jpg
 
After the sawing of the 2mm strips I have now all these on neat gaps, straightened and sanded.
The still black stripes come then in 3mm Plexi
 
img_2746vbl2o.jpg
 
Which I have sawn out next
 
img_2747xll1v.jpg
 
Now I fixed all strips with double-sided tape and the dimensions for the base plate marked
 
img_2750dbz6v.jpg
 
Then I have the 2mm Plexiglas again completely ground, cleaned and with double-sided tape on a sheet glued so that it does not fly away from the paint.
 
img_2751brass.jpg
 
The base plate is now also tailored
 
img_27529nbal.jpg
 
The edges I have all slanted to the half to 45 degrees. The outer edges with the top cutter and the inner edges by hand
 
img_2759qzx42.jpg
 
The sheet metal for the Midtray was now completely cut and then folded.(bent)
 
img_2766biase.jpg
 
img_276794l1m.jpg
 
Now I have cut 2mm aluminum for the PSU cover and cut a few small angles as a bracket and soldered together (also here: does not ask how, absolute disaster but it holds)
 
img_2776ycymg.jpg
 
img_2779b6l3t.jpg
 
Now I have transferred the designs to the PSU cover
 
img_2784qdbpd.jpg
 
The Aquaero must be a bit deeper, so I have now torn all the surfaces to be sawed
 
img_27852fa7a.jpg
 
Everything still nice straight cut
 
img_2786a9lef.jpg
 
And the section for the PSU still slightly bevelled
 
img_2787ksawh.jpg
 
 
So that would be status quo.
Next, I'm trying to create an inlay for the PSU window, hope it works out the way I've seen it with some others. Is indeed something angular.
And for the front of the case I'm still looking for inspiration. I just can not think of what I do best under the arrows, where the Cooler Master logo sits. Something has to be there because otherwise it looks boring.




So many thanks for reading, until the next update!;-)
Edited by capten

Share this post


Link to post
Share on other sites
capten    6

Hi Guys!



Go on.
After transferring the designs to the Plexiglas, I also cut these out

img_27894wuys.jpg

then tailored for the small strip on the far left a few times 2mm strips

img_2790keubr.jpg

Actually the red plexiglass should be polished but these small 2 x 20mm strips all the same to grind brought me to white heat. So I glued the small stripes with epoxy glue to the aluminum and just sanded them after curing.
The Red Plexiglas later foiled everything anyway. I just wanted the UV effect of the polished edges. But in this one place I will be able to cope with it. These strips are then painted with. :wink:

img_279711uyq.jpg

img_2808gfuwt.jpg

Two aluminum brackets have now been cut for the holder of the Aquaero

img_2792o5ukw.jpg

img_2793seui7.jpg

In this form, the entire cover did not fit into the PSU bay anymore. I thought I had to shorten the whole aperture still a bit but the angle adjust has also helped.

img_2798oiuuj.jpg

Since I have failed with the actual midtray miserably as far as the soldering, but it left me no rest,
I still had to practice and test something.
Screws I wanted here actually very reluctant.
Somehow it worked then, I believe at least.
It looked quite ok for a few remnants

img_2805mfu60.jpg

So I now ventured to the correct angle.
Everything with as little contact with other surfaces so that the heat can not be dissipated as quickly and as a base a granite slab. Last but not least, the veneer of the workbench flown around my ears, they gave a loud bang XD!
So everything neatly sanded and degreased and then everything for soldering eigespannt.

img_2804eluqa.jpg

img_2806b2ufe.jpg

I am really satisfied with the result. In the sample I did not have such good capillary action.

img_2807c0u09.jpg

The window for the PSU I now cut from 2mm Plexiglas and polished all edges.

img_2794sdu5z.jpg

img_2795j8uxz.jpg

I have now completely glued on a 1cm larger plate

img_2824hoj1n.jpg

Is a little bubble but I like the effect. Thanks to the brass pipes of the water cooling you will not see any water in the system anyway.

img_2799viumt.jpg

img_2801leuim.jpg

The holes for the PSU aperture were still set at an angle behind I cut thread

img_2802fbun6.jpg

img_2803z6ukt.jpg

The patterns for the front I have all transferred to 2mm Plexiglas and sawn.
Who knows?
Here I have already made the first changes to the original file?
I have here, incidentally, two 2mm slices glued together and both with a dishwashing cut;)
 
img_2809rvum6.jpg

img_2810t0u5h.jpg

The two elements above the arrows I have cut from 2mm aluminum because I want to bend here a small rod

img_28112ruao.jpg

img_2812zzjdw.jpg

I have now marked these rods and cut them with the fine-boring grinder, which, by the way, did not say goodbye after two years. Man again buy new machine grrr
These I then clamped between two steel strips and worked something with the hammer until I was satisfied

img_2813aejcn.jpg

img_2814juk8i.jpg

Jooooo, So beautiful I could not even imagine it  :D

img_2816ugjie.jpg

Oh so on Sunday I wanted to spare my neighbors times a bit so I began to polish some parts of the red plexiglass

img_28180ojxw.jpg

All these here
I cut off all cutting edges with a Cutta blade, then polished from 320 (400, 600,) to 800 paper wet and finally polished with two polishing pastes on high gloss.
Pagan work, man man and that was not even half

img_281941jc1.jpg

In order to see slowly times to go forward I began yesterday with the paint.
Will finally also see whether it all acts as I imagine it before it goes with the other surfaces.
Aluminum got a special 1 / K aluminum primer and the Plexiglas I primed with plastic adhesion mediator.
Then continue working with spraying spatula.

img_2820hbkjf.jpg

img_2822xtk4v.jpg

My workshop is definitely too small  :|

So then, let's see how far I come next week.

Share this post


Link to post
Share on other sites
capten    6


So it goes, after I had to grind all parts again and rework

img_2826atocz.jpg

Everything was painted

img_28275erma.jpg

img_2829scrwn.jpg

Afterwards, all parts were fixed to the base plate and glued with Acrifix 1S 0116.

img_283048q73.jpg

As expected, of course, I slipped a few times with the syringe, damn grrr

img_2831vnq4m.jpg

img_28320xruy.jpg

The attempt to paint it was not particularly satisfying. I will foliate the places later

img_2833k4qd7.jpg

Despite all this, I am very satisfied with the color concept. I like it:thumbsup:

img_2836ripdu.jpg

After a long time, I think a good design for the front and the top. It is a mixture of 2mm and 3mm Plexiglas combined in high gloss and matt.
So now I began to transfer all the patterns to the Plexiglas and cut them out
The front

img_2838v5rfs.jpg

and the top

img_2839ukq7h.jpg

img_284042rfw.jpg

Besides, I disconnect a graphics card from Light Glass, it hurt: heul
and this converted to Bitspower.
For that, the PCI bracket had to be folded again and painted black

img_2841rfqfz.jpg

img_2844s0r13.jpg

img_2845bspcv.jpg

img_2846g8q3d.jpg

For the HDD Cover I now still cut a second plate in white and for the strip of the front plexiglass 2x6mm

img_2847syq9v.jpg

All parts for the top and the front are now bevelled (is there a term for this in English?)

img_2848edqzi.jpg

Now the Coolermaster logo away with 2x polyester 2 / K spatula

img_2849uqq4v.jpg

And then I glued the 6mm strips on the front, fixed with seconds glue and the outer edges all closed with Acrifix, really complicated because the front is slightly bent.

img_2850yxqio.jpg

after the glue was dry, I then again revised the ends of the strips until all straightened with hand and power file, minor damage were 2 / K spatula

img_2851yto0w.jpg

Then everything again primed and varnished

img_285248u1t.jpg

img_2855dnu3c.jpg

Now the edges of the white plate are polished and

img_2854fauty.jpg

So the result.
Here everything is already positioned for the water cooling and measured whether everything fits so far.
Therefore only the pipes have to be cut.

img_2857hkud3.jpg

so then, see you soon!

  • Upvote 1

Share this post


Link to post
Share on other sites
capten    6


Here is the next update!
I could last night unfortunately only 3h sleep then work 9h and 20.00 we have to take a night shift so I shall be brief

There is not much to say, the pictures speak for themselves.
Since the red film is a little translucent, I decided to double everything with film, so first black and then red.
Here are the small items around the PSU Window.

img_2858gysp8.jpg

Then I the last week only polished

img_2859vvsfo.jpg

img_2860aosa9.jpg

img_2861epsfg.jpg

img_2863slstn.jpg

img_2864rmsv5.jpg

img_2865ubspr.jpg

The black plexiglass was only frosted with 600 wet abrasive paper.
Is hardly recognizable in the photos.

img_2866dlsoq.jpg

img_2869bysgz.jpg

img_2870ovsn0.jpg

img_28735gsn0.jpg

Then it went to filming, first everything with black foil and then with red foil

img_28759fsz0.jpg

Comes cool 8)

img_2876stsc9.jpg

The small elements of the PSU window were made of burgundy foil which fits perfectly to the mainboard, the red foil is matching the case

img_28773qs64.jpg

Then everything was glued with transparent silicone to the Windows

img_2878lhsgo.jpg

img_287934s9i.jpg

And then lettering with white foil

img_2882jfsls.jpg

img_2883yvs1k.jpg

Here the PSU window, glued with silicone, the small varnished strip I have previously covered with the burgundy foil

img_28848ts0w.jpg

At the front there were some problems, as the front is slightly arched, the plexiglass was under tension and did not hold.
So everything had to clean again and paint again.
The plexiglass I have still slightly warmed and bent before the second attempt before I have attached it with epoxy glue.

img_2885n4sx0.jpg

With the other elements I am exactly the same.
Yeah !! I like it  :D

img_28861gsdf.jpg

Unfortunately, I had occasionally epoxy glue on the hands and the many cleaning of the surfaces, the paint was so strongly attacked that I had to paint everything again.
I really wanted to avoid it, but I could not let that happen.

img_28870mscg.jpg

img_28883iser.jpg

img_2889h0sia.jpg

Soo I like it better

img_2890ulspw.jpg

Short and sweet :wink:
This week comes the top and hope also the cable sleeving or tubing.   8o

Share this post


Link to post
Share on other sites
capten    6


It's Monday, time for next update;)



Now I've upgraded the backplate visually.
For this I have two red 3mm plexiglas plates cut and glued together

img_2905upkq9.jpg

img_290667kjl.jpg

Then I cut these a few days later in shape and from 3mm to 6mm slanted obliquely, it unfortunately got badly photographed

img_2913dxjoj.jpg

img_2921zejgo.jpg

Then everything completely matted and glued to the GPU.
I've also added some of the motherboard's design.

img_2923mmjyt.jpg

img_2928gok5t.jpg

Then it went with the foiling of the parts of the top

img_29075ssw4.jpg

Because then I noticed that the foil to little is. Well sometimes you have to see it all before you.
I then began to edit the parts again

img_2908kqsgi.jpg

Besides, I have cut a new logo for the front and painted this silver

img_291435sjj.jpg

img_2915zjso9.jpg

Now I finally finished all the parts and glued to the case with epoxy glue

img_29169tsqe.jpg

img_29325vsti.jpg

img_29336zshl.jpg

Then it was time to lay pipes

img_289547suo.jpg

Also here a few holes had to be set

img_28995zsxs.jpg

matching the honeycomb design I have two spacers built so that the case does not protrude throughs so far inward

img_2937g1sl7.jpg

img_2939vpsey.jpg

And here the finished loop

img_2948szspg.jpg

As you can see in the last picture, all PCI Thumscrews were exchanged for white, and others were used at PSU

img_2943xdsqs.jpg

Somehow I thought the PSU cover was too unstable, the gap around the Aquaero have often changed. I thought 2mm Alu would be enough but so I now have two aluminum angles cut, primed, painted and glued to the PSU Window

img_29500uste.jpg

img_2953z3ssf.jpg

Yesterday I started already with the sleeving of the cables. Actually already last week but with the Masterwatt is a sleeving 1: 1 not possible so I had to reject the plan and create now only Extension.
The pump I have already finished :rolleyes:

img_2951u0sm7.jpg

So it is slowly coming to an end, but it still remains exciting as the cables all can be optimally laid and above all as I bring everything to the Aquaero:vain:

Share this post


Link to post
Share on other sites
capten    6

Now the next update.


Before the Cebit did not have much time and now I wait for the mod to come back again:D

So ..... what had to be done:
For the correct installation of the front radiator a few holes had to be changed

img_2955qlpdn.jpg

img_295641qti.jpg

The HDD cover got to fix still angle

img_29578ao8v.jpg

The Aquaero has now finally its black aperture

img_2977vwp2x.jpg

The Flexlights for the interior and the PSu Window were soldered and sleeved

img_304529p5g.jpg

In the midtray was still a hole for a few MB cables and the GPU lighting set

img_304976rv6.jpg

The Sata cables I have shortened to a single connection. This is also quite easy. From the last Sata connection simply the cap carefully lever off and then the cable over the required plug as scarce as possible cut off. Now put the cap back on exactly this plug and done

img_30593lq9p.jpg

img_3060gdpox.jpg

At the MB tray was as always exactly there a strut where the ATX cable should run, so also had to be helped here again.

img_29794yq8q.jpg

Since I no longer need the grommets of the midtray I could make a new execution for this big hole

img_29769xr2w.jpg

At the top there was still a vacancy which looked a bit dull, so I cut a little bit of aluminum, painted it and then covered with the red foil

_mg_3079qbqp6.jpg

_mg_3084gwoxh.jpg

The extensions are now all ready

_mg_2998j0rs0.jpg

_mg_3002s9ozo.jpg

Since one under the IO-Shield the radiator saw had to be made for this still a small aperture
First the pattern taken

_mg_3068c9p01.jpg

Then cut out the appropriate piece from the front grille

_mg_3069h4qq3.jpg

On this grid are two stripes which I originally wanted to leave in red.
First sawn a 3mm strip and then ground in shape

_mg_3070qgo6v.jpg

In red but it did not really fit so I painted black with two layers of clear lacquer

_mg_3078lmqea.jpg

The whole I then somewhat offset to the front fixed and with silicone glued

img_3081ayoug.jpg

Shortly before I have still two red LEDs set so that the slots in the front light

_mg_3036x0s10.jpg

All cables tidy hidden under the insulation

_mg_303783ska.jpg

_mg_3044p2s2c.jpg

The GPU got red LEDs

_mg_30237js9j.jpg

The headset I have now also an individual touch given

img_3062tfsn3.jpg

img_3075lgsq0.jpg

img_30763nsof.jpg

Since the mussels are slightly arched, the Plexiglas had to be slightly bent

img_30772ws06.jpg

img_3082tqsyi.jpg

The PSU Window left me no rest. I then found a good tutorial for cementing plexiglass.
Important is polyester adhesive tape. So again a small window cut, adjusted, polished edges.
Apply the polyester adhesive tape completely to the surface to be glued, then place the window on it and gently cut it with the scalpel once. So I now have a perfectly mashed surface.
Remove the center tape now, of course. Then apply abundant to full acryfix and press the window gently free of bubbles.

_mg_2973m5s94.jpg

This time I have accelerated the drying process additionally with UV light, just in bad weather, the sunlight simply does not matter. I think it was also often to bubble formation so that the glue usually after 24h was not 100% hard. With the UV light I could break off the glue easily after 3 hours with a chisel.

_mg_2978l3smg.jpg

Stupid, I have the window on the wrong side glued XDXD but you can recognize the difference to the first attempt. No more bubbles and full glue on it :wink:

_mg_3013o7sfo.jpg

So all good things are 3. Unfortunately, 4-5 photos from the window have not changed anything but I will finish it in the final pics in detail.

_mg_3024yjsfx.jpg

 _mg_3025rhsq8.jpg

So, because I did not like the burgundy foil on the PSU cover with the red Plexi behind it, I painted it all black. Also the honeycomb covers of the Bitspower housing feedthroughs

_mg_29721jsr7.jpg

And then with the case colored red foil.

_mg_3027hdszd.jpg

The radiators were also painted in white and the slats with a red metallic lacquer

img_2958hkshw.jpg

img_2963x6sab.jpg

In order to make the back a bit more photogenic, I have also continued here the red arrows

_mg_29670ju14.jpg

_mg_2968b3utp.jpg

_mg_2970y6usn.jpg

Also these holes in the case did not please me

_mg_29716wuf4.jpg

then everything foiled red again

_mg_3030o7uzq.jpg

_mg_3032v7uf7.jpg

Now again a dangerous matter. The Windows had to be adjusted something so I can continue to use it. Since some covers were closing in the way, I had to separate something from the steel of the Windows.
Since glass can crack quickly with the sudden contact with heat I am very cautiously proceeded and have repeatedly inserted breaks at the cutting.

img_3063ofuq7.jpg

But first I have the whole window with foil protected and then still an old rag for the protection against spark hung before it.

img_30650sukb.jpg

img_3064v1uul.jpg

img_3066equxw.jpg

So that was it! The memory and SSD has now finally arrived. So once I have the case again I can finally make the final photos  :phat:

img_0180clusa.jpg

Share this post


Link to post
Share on other sites
capten    6

All right, and here the first final outdoor pictures.

 

img_023772xjd.jpg

 

img_026718z12.jpg

 

img_0269vnzvv.jpg

 

img_0274ojzz9.jpg

 

img_0275wty6o.jpg

 

img_0278pmln9.jpg

 

img_0282ouar3.jpg

 

img_0288pta4l.jpg

 

img_0292fzlul.jpg

 

img_03024iln7.jpg

 

img_0306ejzpg.jpg

 

img_0311pfzcs.jpg

 

img_0314c0x4i.jpg

 

img_0322quaip.jpg

 

img_0324xxxmi.jpg

 

img_0326aqzu4.jpg

 

img_033688xpo.jpg

 

img_03384fzni.jpg

 

img_0350wzbyu.jpg

 

img_02052pxuy.jpg

 

indoor pics with lightning comming soon :wink:

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now