Recommended Posts

Welcome everyone. I am Zoli from Hungary. I apologize for my English is a little incomplete. I use Google Translate.

It's time I read the forum and now made up his mind to draw up an own CASECON.

Sponsors For now, no, but that will likely change.

The plan found here. Few restructuring plan on it.

For now, that's it, I'll soon be in the pictures.

The materials used in foamed PVC (Kömatex), glue, aluminum profile and a few screws.

Some pictures unfortunately missed the beginning.

But in the future it will no longer be missed.

post-104579-0-73191900-1457125864_thumb.jpg

post-104579-0-60462100-1457125923_thumb.jpg

post-104579-0-36724900-1457125985_thumb.jpg

Today I prepared the basis for the roof and side panels

The recording side panels, I found out that without screws, sliding method would fit into place.

post-104579-0-71628600-1457126034_thumb.jpg

post-104579-0-34588100-1457126085_thumb.jpg

post-104579-0-64783100-1457126136_thumb.jpg

post-104579-0-25906600-1457126302_thumb.jpg

post-104579-0-57999900-1457126352_thumb.jpg

post-104579-0-56587100-1457126407_thumb.jpg

post-104579-0-02857200-1457126469_thumb.jpg

post-104579-0-69232300-1457126522_thumb.jpg

The other day I made the top of the permanent establishment and the bottom of the grid ,, "also won the pre-final form of power.

post-104579-0-79331000-1457126640_thumb.jpg

post-104579-0-93854000-1457126763_thumb.jpg

I fixed up the top of the tablet holder ,, box. "I've been thinking that either horizontally or vertically to be this. Finally, the vertical won.

post-104579-0-85454500-1457126866_thumb.jpg

Today I did a little brightening up in front of the fairing and painting the top and side panels.

post-104579-0-22678100-1457127414_thumb.jpg

post-104579-0-96224700-1457127479_thumb.jpg

post-104579-0-74155400-1457127530_thumb.jpg

post-104579-0-08523500-1457127789_thumb.jpg

post-104579-0-30605400-1457127840_thumb.jpg

post-104579-0-60107500-1457127988_thumb.jpg

post-104579-0-43700700-1457128061_thumb.jpg

post-104579-0-58085900-1457128119_thumb.jpg

In the course of yesterday's Asrock Hungary and Cooler Master Hungary sent the parts. 4 x 120mm fan, 2 x 92mm fan, and a 850W power supply ITX motherboard with AMD processor.

achment=10723:DSC_0687.JPG]

post-104579-0-84983100-1457128260_thumb.jpg

Hi there. Later today I pulled it a little better. I was thinking over the ground plane, only to vent grille-ended, but I found home 3mm leds. I started to drill in place

post-104579-0-97301300-1457128337_thumb.jpg

post-104579-0-92590900-1457128403_thumb.jpg

post-104579-0-88090800-1457128436_thumb.jpg

post-104579-0-99947100-1457128476_thumb.jpg

post-104579-0-39017900-1457128516_thumb.jpg

Quite a long operation proved. Then I prepared the paint. I affixed the stickers, which I received last night, and at first thought I blew the red parts.

post-104579-0-66256500-1457128605_thumb.jpg

post-104579-0-31879800-1457128644_thumb.jpg

post-104579-0-94127600-1457128697_thumb.jpg

post-104579-0-00660400-1457128781_thumb.jpg

post-104579-0-46020300-1457128822_thumb.jpg

Once dry, I uncovered the correct parts and the whole sprayed metallic black.

I think it was not bad, but it would have to be improved.

post-104579-0-91886100-1457128891_thumb.jpg

post-104579-0-31506600-1457128926_thumb.jpg

post-104579-0-28523400-1457128965_thumb.jpg

post-104579-0-60711400-1457129013_thumb.jpg

post-104579-0-44646200-1457129053_thumb.jpg

post-104579-0-48756200-1457129131_thumb.jpg

post-104579-0-38487100-1457129167_thumb.jpg

post-104579-0-71817000-1457128197_thumb.jpg

Share this post


Link to post
Share on other sites

So it came into operation. The tanks were problems when I put on the cap and it was the plug, not fit under the radiator. I managed to get a 10cm tank, from then it was OK. After uploading a while spinning machine. The truth is that an AMD proc and of a very slim 4950 x2 to the radiator 240, 30 thicknesses. The fans need to spin at full speed.

Then here are the final images.

post-104579-0-11927700-1459402273_thumb.jpgpost-104579-0-26943000-1459402306_thumb.jpgpost-104579-0-77789000-1459402326_thumb.jpgpost-104579-0-65876200-1459402345_thumb.jpgpost-104579-0-84061300-1459402364_thumb.jpgpost-104579-0-19945600-1459402383_thumb.jpgpost-104579-0-28462700-1459402402_thumb.jpgpost-104579-0-32241800-1459402451_thumb.jpgpost-104579-0-57370200-1459402471_thumb.jpgpost-104579-0-96538400-1459402489_thumb.jpgpost-104579-0-06002400-1459402503_thumb.jpg

When everything was finished, I saw bugs in it. But then the next will be better

Thank you for your attention

Share this post


Link to post
Share on other sites
Atila Gobor    0

It started out good... but you could have payed more attention to the paint job... you could have used some putty and  then fine sand it down to have perfect joints.
 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.