Sign in to follow this  
ST.o.CH

[Scratch build] ST.o.CH FACTOR_I

Recommended Posts

ST.o.CH    19
Hello everyone, an update for today, the side doors.

After losing a week in idleness, also because I was waiting of the glass to be able to continue the work.

Another issue is the fact that I have delayed ordering the connectors, 

as that only arrived in March I've dropped out of order, and so my work grows more than expected.

 

The two doors already with glasses on.


39.jpg

40.jpg

41.jpg

42.jpg

43.jpg

44.jpg

45.jpg


After spending more than 40 hours on the doors since the last post, 

in order to reduce working hours I'm going to need a machine for cutting/drilling/router type linear machining, 

apart from the fact that I am satisfied with the work and labor, I also need idle time to muster weird stuff.

That's all for now.

Share this post


Link to post
Share on other sites
ST.o.CH    19
Hello modders, it's been a while.

Although the competition is finished I hope to continue to post on this forum until I have the project ready.

For today I bring the underside that will accommodate deposits and the hinge system.

The painting has given me a lot of work because I haven't been able to get the right color and it's one of the things that I do not understand almost nothing.

Despite the problems that have arisen the good news are the dimensions of the case, which will replace the 331, fits under the desk.

 


46.jpg

47.jpg

48.jpg

49.jpg

50.jpg

51.jpg

Share this post


Link to post
Share on other sites
ST.o.CH    19
Hello everyone, today I bring to you another update,
this time the doors are already in the right place and functioning properly,
the solution was to pull the shaft to the top, and to complicate, the situation got better.
The lower area of the box looked like a ferry boat was crafted in front for the moment, 
and getting the box mounted until it gets well, also some accidents of course the ink level.
 
52.jpg
53.jpg
54.jpg
55.jpg
56.jpg
57.jpg
58.jpg
59.jpg
60.jpg
61.jpg
62.jpg
63.jpg
 

Until next update.

Share this post


Link to post
Share on other sites
ST.o.CH    19
Hello modders, for today I bring another update, the front renewed with the DVD drive in the top position in order to avoid conflicts with the door. The last outside part was the easiest to carry out and the next step will be to dismantle everything, sanding and painting. Inside the box left to do the power supply and access to deposits caps.
By now are these photos, I'm sorry to have taken so long to get here.
64.jpg
65.jpg
66.jpg
67.jpg
68.jpg
69.jpg
 

See you later.

Share this post


Link to post
Share on other sites
ST.o.CH    19
Hello modders, for today I bring a month update of hobby.

The pieces finally met the White right (this glossy white),

The feet are covered in gold leaf, as they have the responsibility to stand

with everything on top. Deposits are actually two fire extinguishers, one of two kg of CO2 and one of six pounds of powder, both lost contents and received internal treatment anti oxygen

(anti-corrosion zinc spray), the visible tubes are for filling of liquid refrigerant.

The blocks and radiator EKWB are well inside the box, because this is being done by measure.

In front, the acrylic jars filled with light and, with the right touch until they are able to change color.

Jokes apart of that I got rid of, just missing the sleeving, covers for the source and disks with

the brand name and, more important, my version of the connectors.


70.jpg

71.jpg

72.jpg

73.jpg

74.jpg

75.jpg

76.jpg

77.jpg

78.jpg

79.jpg

80.jpg

81.jpg

82.jpg

83.jpg

84.jpg

85.jpg

86.jpg

87.jpg

88.jpg

89.jpg

 

Take care.

Share this post


Link to post
Share on other sites
ST.o.CH    19
Greetings,

Here comes a small update, the scheme of fittings and a sample of it.

90.jpg

In the middle is virtue.


91.jpg

92.jpg

93.jpg

94.jpg

95.jpg

96.jpg

97.jpg

98.jpg

Until then, take care.

Share this post


Link to post
Share on other sites
ST.o.CH    19
Greetings modders,
For today I bring the fittings almost done, it’s missing the video card, and the pump cover.
 
99.jpg
100.jpg
 

More to come soon, until then.

Share this post


Link to post
Share on other sites
ST.o.CH    19
Greetings, here's an update.

This week I haven't had much time. Just for complete the pump cover. Also made

the psu cover with the holes to pass the wires, the original fan is green and will be replaced by one white, 

also with 140 mm. Tweaked on the back of the motherboard, and actually went well, I used the M4 holes

and made a box for the hard disk, shown here with an old disk.

In the section of the wires already appears a acrylic part for the wires of the motherboard 

and another mounted on the radiator for the fans and fans leds.

Of rest are photographs of details.

101.jpg

102.jpg

103.jpg

104.jpg

105.jpg

106.jpg

107.jpg

108.jpg

109.jpg

110.jpg

111.jpg

112.jpg

113.jpg

114.jpg

115.jpg

Until next time, take care.

Share this post


Link to post
Share on other sites
ST.o.CH    19
Greetings, here follows a small update for this day.
Made a change in my Artic Extreme II gpu cooler, switch the three 92mm fans for two 120mm Sickleflow, also put 
a home made copper heatsink to vrm and ram. This all together with a huge four slot alu case.
116.jpg
117.jpg
Bleh
118.jpg

To much taller.

119.jpg
120.jpg
121.jpg
122.jpg
123.jpg
Gpu enclosure, take two.
124.jpg
125.jpg
126.jpg
127.jpg
128.jpg
129.jpg
130.jpg
That's all for now, take care.

Share this post


Link to post
Share on other sites
ST.o.CH    19
Hello modders, this is the last update.

I want to thank Peter Sanj and the EKWB for being the first to believe in my project and help me to make it possible.

Here are the photos.


131.jpg

132.jpg

133.jpg

134.jpg

135.jpg

136.jpg

137.jpg

138.jpg

139.jpg

140.jpg

141.jpg

Working with zero leaks.


142.jpg

143.jpg

144.jpg

145.jpg

146.jpg

Lights on.


147.jpg

148.jpg

149.jpg

150.jpg

151.jpg

152.jpg

Spectrum.


153.jpg

154.jpg

The G3n3s1s and FACTOR_I together, different styles and attributes.


155.jpg

156.jpg

157.jpg

158.jpg

159.jpg

160.jpg

161.jpg

And also thanks to the community for the feedback.





Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this