Sign in to follow this  
Rikuntyudady

HAF922 MOD

Recommended Posts

Hello,everyone.

Only a few was able to do work today also.

They are the part of a front painted the other day, and a part of heavens side. :D

A corrugate tube is painted in silver.

158014776_org.v1351342606.jpg

Although there were some by which plating paint was carried out, though it was regrettable, the thing of just right thickness was not found. :(

A hole is made in some parts of a front.

158014707_org.v1351342583.jpg

Although processing should be essentially finished before paint, I always act off the top of my head. :mrgreen:

It lets the painted tube pass in a hole.

158014734_org.v1351342590.jpg

This is attached to a total of six right and left.

However, it is after painting topcoat with urethane.

158014756_org.v1351342599.jpg

It is check work this time.

The smoke acrylic pioece is embedded to the resin part of the omitted heavens side.

158014646_org.v1351342559.jpg

A rear portion is covered with an acrylic board.

158014665_org.v1351342567.jpg

158014689_org.v1351349220.jpg

However, this portion may be changed into a mesh.

Thank you for seeing.

I will report again in a few days. :hello2:

Share this post


Link to post
Share on other sites

Hello, everyone.

The part of the top portion was painted today.

The outside will be completion, if it waits to dry the rest and topcoat is made all by urethane clearance. :cheers:

It paints to metallic dark grey like the part of a front.

Then, a rivet effect is added.

158161739_org.v1351426940.jpg

In order to paint some tops with a fluorescence orange, it paints in a white once.

It is for improving coloring of a fluorescence orange.

158161760_org.v1351426948.jpg

It paints with a fluorescence orange.

158161792_org.v1351426960.jpg

Coloring of this has followed MY GEAR(HAF932 CASE MOD) performed before.

It is because they are their brothers. :mrgreen:

Before painting a urethane clearance, you have to make it fully dry.

The work of an inside is continued while waiting for dryness.

Thank you for seeing.

I will report again in a few days. :hello2:

Share this post


Link to post
Share on other sites

Hello,everyone. :D

This time, I carried out topcoat of each part which finished paint.

159072054_org.v1352037052.jpg

Decal was stuck on the top part.

159072087_org.v1352037060.jpg

159072109_org.v1352037068.jpg

And although it was going to carry out the 2nd clear coat today, it had changed into such a state. :pale:

159072141_org.v1352037075.jpg

OMG...

It was eroded by the solvent of the urethane paint and the line has loomed. :angel5:

Although correction was applied, in order to have to wait to get dry completely again, work does not follow it for one week.

It is becoming really uneasy about whether it does on a deadline. ((((;゚Д゚))))

However, I will do my best.

Thank you for seeing.

I will report again in a few days. :hello2:

Share this post


Link to post
Share on other sites

Hello,everyone.

Although the 2nd urethane paint was carried out today, work is not progressing other than it. :(

ATCS840 which is carrying out synchronization is the waiting for dryness now.

Only a few introduces a part of work of "CoolerMaster SNIPER MOD" further today. :mrgreen:

159423428_org.v1352301277.jpg

159423401_org.v1352301559.jpg

159423511_org.v1352301540.jpg

159423485_org.v1352301540.jpg

Since SNIPER was due to be made into the military style, the damage effect was given to it at the lock portion of a 5.25-inch bay and HDD mounter in all.

I am sorry for the picture which is unrelated to HAF922.

Moreover, it reports in a few days.

Thank you for seeing. :hello2:

Share this post


Link to post
Share on other sites
Very impressive & authentic look you have pulled off with the painting of the 5.25-inch bay and HDD mount :D

Thank you for your comments!!

Possibly a few was done too much.

If it completes, it may be mistaken for garbage by the wife and may be thrown away. :mrgreen:

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this