Search the Community

Showing results for tags 'wiring'.



More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Campaign
    • Case Mod World Series 2019
  • Announcements and Giveaways
    • Announcements
    • Giveaways
    • CES & Computex
  • PC Building Guide
    • Reviews and Unboxing
    • Build Advice
    • Build Worklogs
  • Hardware
    • Cooling
    • Cases
    • Power Supplies
    • Peripherals
  • General Discussion
    • General Hardware
    • Overclocking
    • Game Zone
    • Product Suggestions
  • Modding
    • Mod Lounge
    • Mod Worklogs
    • Mod Contests

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests

Found 5 results

  1. Hello, I just built my PC. Firstly I wired Wraith Prism via RGB header and controled RGB by motherboard UEFI. The range of presets was not very rich, so I rewired cooler as option 2 (via USB Header). It works, but original software from CM doesn't detect it and says: "Plug it your CM device to get started"". So, where I made a mistake? Please suggest. Thanks
  2. I've just completed my first PC build using the MC 500mt as the case. There's a control box on the back for the fans and the rgb lighting included with the case. I cannot figure out the wiring for this as none of the fans or the rgb panel inside the case are working. When I figured out that software was also required I installed it only to receive a message to "Plug in your CM device to get started. The instructions that came with the case are useless or I'm just too new at this. I assumed the "controller" would be set to go but I'm guessing that additional wiring is required. Fans are plugged in, rgb light panel is plugged in, there's one pin plug in the bottom left side and one connector on the bottom right without anything plugged into it. Is that suppose to be connected somewhere somehow? Thanks for any help. Guessing it's something simple. Better documentation Cooler Master please!
  3. I would like to use the MasterLiquid Pro 280 paired with an ATX power supply and a PWM fan controller in a cooling application without a PC motherboard. However, I cannot find a 4-pin PWM fan controller; I've only found 3-pin controllers (some of which claim to use PWM over the 3-wire connections). If I use a 3-wire PWM controller with the 4-wire MasterLiquid Pro 280, will I damage the control circuitry on the pump or fans? If I use a 3-wire voltage-varying controller with the MasterLiquid Pro 280, will it damage the pump or fans? If so, could you recommend a fan/pump controller for me to use? Thank you, Adam J.
  4. The wiring for the panel is made up of twisted pairs. Each pair has ( 1 ) colored wire and ( 1 ) white wire. I have interpreted the colored wire as the power ( + ) and the white wire as the ground ( - ). The case is a Cooler Master HAF X Full Tower, model number RC-942-KKN1. Is this correct? Thank you for your help.
  5. Hello please help me with my problem. i have the trooper case und in the middle of the panel is the button to switch the fan led on or off. i have 2 new fans mounted (Enermax T.B.Vegas 12cm red led) the have also a button to switch the leds (no on-off switch, only a button like the panel one) is it possible to connect the 2pin cable coming from the front panel to the 2 pin cable instead of the fan button ? (attached a pic from the fan cablebutton) i hope you know what i mean & understand my english thanks for the info greeting Martin