Search the Community

Showing results for tags 'Pump'.



More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Case Mod World Series 2017
    • Case Mod World Series 2017
  • Announcements and Giveaways
    • Announcements
    • Giveaways
    • CES & Computex
  • PC Building Guide
    • Reviews and Unboxing
    • Build Advice
    • Build Worklogs
  • Hardware
    • Cooling
    • Cases
    • Power Supplies
    • Peripherals
  • General Discussion
    • General Hardware
    • Overclocking
    • Game Zone
    • Product Suggestions
  • Modding
    • Mod Lounge
    • Mod Worklogs
    • Mod Contests

Calendars

  • Community Calendar

Found 6 results

  1. Pump Malfunction?

    Recently while using my PC under load the temperatures of my CPU would go above 90 degrees Celsius. Upon restarting my PC it would give me a "CPU FAN ERROR". When I checked my bios, it showed that my CPU fan was at 0rpm. Then instead of plugging the pump into CPU_FAN I plugged it into CPU_OPT and now that one shows 0 rpm instead. When I physically checked the 2 fans attached to the radiator, they were still spinning. This led me to believe that the pump has failed but I am not sure if this is how to properly check if the pump has failed or not and would like further clarification. Also I would like to know how I can go about replacing it using my warranty if it is indeed a pump fail, thanks
  2. My ROG MAXIMUS X HERO mother board has 3 ports: AIO PUMP, CPU OPT, AND CPU FAN. The CPU OPT and CPU FAN have the same pin out configurations I know the pump connect goes into the AIO PUMP port. My question is can I plug one fan into the CUP OPT and one fan into the CPU FAN and not use the splitter? Will that mess up the fan control balance between the two? Do I have to do anything in the fan control bios software to keep them in sync or does it matter? Or Must I use the splitter and just the fan port? Thank you, Bill
  3. Pump stopped working

    The cooler has been working fine for almost three years. It stopped working briefly, once, a long time ago—I tapped on it the pump and it seemed to be back to normal—until last night. The pump seems to have stopped working, permanently. The blue LED is still lit, but the BIOS reports 0 RPM on my Gigabyte motherboard, the radiator fan is on, high ( > 2300RPM), and my CPU temp quickly runs past 91º+. It is only a matter of minutes before Windows shuts down with a critical error. I'm running an i7-4770K (not currently accelerated). What could have triggered this? Is there anything I can do to fix it?
  4. Hello you cooler fellas and gals, this would be my first post and in good tradition it comes with a question attached. So lets hope you guys can answer or point in right direction, (no, not the exit door ) So I have a Asus TUF Mark 1, this motherboard has a 1x dedicated pump 4 pin header and the 2x 4pin CPU fans Now it would be my hope, that I could connect the MasterLiquid Pro 240 pump to this dedicated pump header and the fans to the 4 pin fans CPU1 and CPU2. Would that be a feasible and acceptable setup? ill admit Im not familiar with the MasterLiquid Pro 240 or liquid cooling in general, but much research has been done on this lately. Ive read the manuals and searched around but maybe Ive missed something. Im replacing a Corsair Hydro H100i V2 with this MasterLiquid Pro 240, Corsair has gone on the naughty list, and wont even get a piece of coal, but will definitely get the boot... soon. So here is hoping.
  5. Glacer ver.2 Flow Direction?

    HI all, I just picked up the Glacer and i want to expand it to my Asus Maximus VII formula. I was curious if anybody had a flow diagram so the Res/Rad will feed the pump and not my VRM cooler first?
  6. Nepton 280L vs Nepton 240M

    Which is better? Nepton 280L or Nepton 240M? In many reviews, Nepton 280L cooling performance is a bit better than Nepton 240M. However Nepton 240M is amazingly quiet. (Cooling performance is my main concern.) I would like to ask, if the pump of Nepton 240M is the same one as Nepton 280L? Or which one is more powerful? I am wondering if I choose Nepton 280L, and replace it with another quiet and powerful fan, will I get the best performance with the quietest system? Thanks for any inputs.