Search the Community
Showing results for tags 'sff'.
Found 4 results
Hello everyone - Welcome to my build log for my current project, a scratch-built PC / Games Console designed for the living room. About the Build: After my previous project was primarily built from used components and recovered materials, I wanted to design and build something new and bespoke, with materials sourced for the purpose of the build. The move to smaller cases and living room PC's was also an area that I've found really interesting recently; lots of great designs from both big manufacturers and modders alike. So this is my attempt at the same challenge. I'll be including as much of the design process as I can, as well as the actual building (the design phases pre-build were very important!) The Build Spec - Primary Requirements: - Powerful enough to play games and compete with other living room systems - Small enough to fit in a unit under the TV and not look out of place (i.e. flat) - Quiet enough that it doesn't ruin the gaming/TV experience - The design must represent a visual showcase, one that provides Diesel Engine with a unique and clear identity. Secondary requirements: - The software must boot directly into a gamepad-navigable state. No Keyboard + Mouse - The case must not light up like the sun (this is very distracting when sitting under the TV) - The case should not use or require any specialist or custom hardware - Be able to support both 1080p and 4K system setups - Not require an external power brick Oh... (and this should go without saying) but the build shall not call itself an "ITX case" and still support full size ATX hardware and all the trimmings. Concept Artwork I drew and modelled a range of concept pieces first, free from any technical limitations, just so I could see where the art style was heading. Once the style was chosen, only then would I start to figure out if the design was technically feasible. A similar half and half design to the Xbox One and PS4, which have matt and gloss surfaces. A chunky hexagonal design in copper plate also sounded great A very slim, long and simple design. Minimising or hiding all controls and inputs from the front I explored some of the same shapes and colours in 3D, using Sketchup to create some quick and dirty mockups By this point I was aware of the size of ITX and SFF components and had a rough case size in mind. This helped me work with some units when modelling Technical Design I decided to pursue and modify Concept 2#, it was a simpler design and there were areas of Concept 1# would be technically more difficult to implement. I needed to determine what parts of the design were feasible and the layout of the components within the case. There were three main parts of the design up for negotiation: orientation of the graphics card, form factor of the power supply, choice of supported components and airflow solutions. It's worth mentioning here that I had also started investigating materials and fixtures. Like many cases, sheet steel construction would provide the strength and simplicity that I required for the inner shell. I planned on using premium materials to cover the steel shell and where possible, be fixed from the inside of the case so that no screws would be on show. My technical designs started to consider how the pieces would be made from bent sheel material and fit together. I had experience using graphics card riser cables, so I knew that I would be able to re-orientate the card how I liked. Many other HTPC cases that I had seen use rigid risers and have the card fan facing downwards. I really didn't want this, it was important that performance cards get fresh air from outside the case so I wanted the fan to be as close to the console lid as possible. I planned to incorporate a design into the lid that provided direct airflow to the components. I built a bunch of scale models to check the real-size of components. SFX and Flex ATX power supplies here. I'd recommend this technique since 3D models can sometimes detach you from the relative size of objects. An ITX motherboard and a SFX/short graphics card. Side note: the questionable meatballs are NOT mine I chose the Flex ATX form factor for its tiny height, just 40mm! The SFX power supplies were around 80mm and up. I started modelling and worked on translating my concept designs into a technical design I decided the simplest layout of positioning the components next to each other would allow me to keep the case in a flat console style. I explored a bunch of different front port options Investigating ways that the Graphics car mounting would work in the simplest way I started mapping the mounting holes for Flex ATX PSUs The front panel assembly for the USB's + power button was something that I would have to create. This was an early solution I came up with. The tolerances were going to be tight. I learned that folding very near holes in the sheet would likely compromise the shape of the hole, so I had to redesign some sections several times. I was having the same problem with the graphics car supports and was unsure if they would still hold thier shape after being bent Final Design I combined the learnings from my technical design investigation and produced a final concept design of what the case was going to look like and how it was going to work. The final design includes ventilation in the lid, mounting for all components, a front panel assembly and cable management solutions. I was also able to find solutions that would allow me to construct the case from the inside, hiding nearly all of the screw heads. Having a solid technical design also allowed me to go back and design the asthetic parts of the console, knowing that it would be feasible to create. I had started searching online to see what kinds of parts were freely available: thin panels of real wood, thin and affordable premium metal panels, fixtures. ....And there you have it! During the design of the final concept I also nailed down a lot of the technical details that you see in the images above. I'll go into more detail about the shell design next post and explain the role the of the spacers and also why I chose to separate the case into several different pieces. Other small decisions like the position of the power button were finalised, I really liked the idea and look of cutting the corner off the case. I also began using CAD software to translate my sheet designs into something that can be fed into a machine and made. I have many tips and learnings from that exercise that I can share here. Before I leave the first post, I should probably show some work in progress right? Oh okay, can you tell what it is yet?
Introduction: Hi Guys, First of all, I'm Andrew Lee Adanza. I've been a pc enthusiast for just about a 2 years or so. Building a gaming rig was only my goal at that time. But as time/months passed by, my love for PC grew. That is the time when i was hooked up to modding. Right now, i'm in a foreign land and it is hard for me to grab all tools and materials to do modding since im still not familiar in this country. Anyways, I will stop this nonsense and proceed with my build log. I've already seen and followed some epic system builds and project logs creating a case using acrylic. some of these are wallmounted pc's like LORAMENTUM and some build using PARVUM like Darthbeavis, l3p, kier etc. This guys inspire me. so now, I will be creating a case with the idea of a case made of acrylic like PARVUM but with inline loops(coolant will pass in the case itself, like LORAMENTUM). If my work comes out half as good as other "masterpiece". It would be a great achievement for me. All cuts are done using a scrollsaw and by hand. hoping to have my own laser cutter to ease the work. I would also like to take this chance to say thanks to all of the sponsors. Thanks BITFENIX for sponsoring this build. Special thanks to BitFenix Malaysia and Clement for all the help. Thanks CORSAIR for sponsoring this build. Special thanks to Corsair Malaysia, Emily and Anson for all the help. Thank you guys. I would also like to give thanks to Intel and Intel Malaysia for helping me on this build. Thanks a lot guys. And to my wallet. hehehehehehe.... If you want to see our upcoming projects, you can visit https://www.facebook.com/arcismodz Thanks ====================================================== Hardware List: Below is the list of parts/hardwares to be used in this build. Specs: CPU: I7 4790K - âœ“ MoBo: Asus Z97i - Plus - âœ“ RAM: Dominator Platinum 2400mhz - 2 x 8gb - âœ“ GPU: GTX 760 - âœ“ (to follow, all budget for GPU goes down the drain with all the tools and materials needed for this build.) HDD: WD 500gb - âœ“ SSD: Corsair Neutron 240gb PSU: Corsair AX760 - âœ“ Water Cooling: CPU Block: EK Supremacy CPU Block Nickel Plexy - âœ“ GPU Block: EK FC670/760 - âœ“ Rad: Black Ice GT Stealth 240 XFlow Rad - âœ“ Pump: EK DCP 4.0 Pump - âœ“ Reservoir: D65 x L170mm RES - âœ“ Fittings: Compression Fitting - âœ“ Fittings: 45 Degree Adapter - âœ“ Fittings: 90 Degree Adapter - âœ“ Flex Tube: Primochill Advanced LRT Tube - âœ“ Coolant: Mayhem Pastel Green/Mayhem Blue Dye/Mayhem UV Green-Yellow Dye - custom color - âœ“ MODS and Misc: Fans 1: CM JetFlo 120 2pcs - âœ“ Fans 2: CM XtraFlo 12CM 2pcs - âœ“ Led Lights: BitFenix Alchemy LED Strips(white) - âœ“ Sleeved Extension Cables: BitFenix Alchemy Cables - âœ“ Corsair Lightbar Kit Hardware Photos: Box Photos: Hardware testing/my current setup
I built my first PC a couple of years ago and my enthusiasm for making PCs has grown. I'm a university student who wants to get into the case modding hobby. I have no sponsors as I am new to the scene. Current status: PROJECT COMPLETED! Page 5 has final pics. I am going to start with a very ambitious project of fitting a HIGH-END gaming PC into not much larger than a popular gaming console with no thermal compromises. Intended for LANs or just as space-saving without losing on performance. Will fit most backpacks with ease along with peripherals and cables. The specs for the PC are as follows: PSU: Athena Power AP-MFATX50P8 500W 1U-FlexATX. Modified. MB: Gigabyte H87N-WiFi Rev2.0 CPU: Intel Core i5-4670 3.8GHz Cooler: Silverstone NT07-115X Fan: CoolerMaster XtraFlo Slim 120mm PWM RAM: Kingston ValueRAM Low-Profile 1600MHz 1x8GB DDR3 SSD: Samsung 840 EVO 500GB GPU: EVGA GTX 970 SuperClocked ACX2.0 (overclocked to 1500MHz core, 7400Mhz effective memory) WiFi: Using internal antennas. Realtek RTL8191SE 1x2 300Mbps 802.11 b/g/n half mini PCI-E card. Upgradable to an 'ac' card if needed. LEDs: Custom RGB LED controller linked to PC through the motherboard's Serial Port Header. The specs of the case are currently as follows (will update when changes are made): >>>>>>>>>>>> Volume: 5.07 Litres <<<<<<<<<<<<<< Dimensions: 311x267x61mm (WxDxH) Material: Clear Acrylic (10mm sides. 6mm top/bottom/divider.) Front Panel: Power button, HD Audio jacks, 2 x USB3.0 Ports. (RGB LEDs will serve as power light. HDD light will be on the motherboard.) Max GPU length: 255mm (will take either EVGA ACX2.0, Zotac 900-series or any brand's Mini-ITX variant.) Max CPU Cooler Height: 25mm (or 40mm without the slim 120mm case fan) Drive Support: One 2.5" SSD or Hard Drive Reference Dimensions: Game Consoles PS4: 305x274x53 4.45L (My case is just 14% larger than this) XBO: 343x263x80 7.22L (My case is 30% smaller than this) Silverstone Cases RVZ02: 350x350x80 9.80L SG06: 220x177x286 11.14L PS08: 355x168x400 23.86L Other details: Power socket for the PSU will be re-wired to a rear IEC socket. Don't want to have the power socket on the side of the case. Intel stock cooler does not fit (height). A Silverstone NT07-115X and a CoolerMaster XtraFlo Slim 120mm fan on the roof of the case blowing downwards (intake) will be used. This will provide fresh air to the undersized CPU cooler and cool the rest of the motherboard components. Rear panel will be tailored for this specific motherboard (or its Z87 variant). I will not be using the I/O shield as it cannot fit. Various lengths of M3 bolts will hold everything together. The divider will be held in place by slots built into the top and bottom pieces. The GPU will connect to the motherboard via a PCI-E 16x 2U Riser Card. The GPU will be held in place by the PCI-E Riser Card and a bracket on the rear of the case. As well as a rubber bumper near the end to keep it straight and reduce shock when transporting. The RGB LED controller will be an Arduino microcontroller (pro mini variant) and a custom MOSFET circuit along with a RS232 to TTL level shifter. It will connect to the Serial Port header of this motherboard. This can be controlled via a serial terminal from the desktop or via an easily-coded GUI. GPU PCI-E 6-pin power plugs will be partially in the wall of the case (they stick out a fair bit) as well as being cut down slightly to reduce their profile. A metal panel will be mounted over this hole. (Better explained visually.) Thermal Design: The CPU and GPU area is separated by a divider with only holes large enough for the PCI-E power cable and riser card. This will isolate heat from the GPU from entering the CPU area. The EVGA ACX2.0 sucks in air through the bottom and side of the case. It expels the hot air mostly out the Rear and Front of the case. All these areas are well vented. The CPU area is vented. The CoolerMaster XtraFlo 120mm fan will be blowing downwards and pushing out any small gaps and vents, as well as supplying fresh air directly to the small CPU cooler. The Power Supply sucks air in through its own vent through the bottom of the case. All air is expelled out the side of the case from the 40mm speed-controlled fan. Pictures speak better than words in this situation. Here are some SketchUp models of the design: Note: Some models from the SketchUp Warehouse were used to show where parts will go. It is for reference only. The GPU is a reference 780 that was scaled down to an EVGA ACX2.0 size. I was lucky to find my motherboard (the Z87 variant of it anyway which is physically the same) on the 3D Warehouse. NOTE: These are not the final renders. These will not be posted. LATEST PICS ON PAGE 3 ONWARDS Empty Front Rear Motherboard side (with PSU exhaust) Bottom Top Soda Can and DVD Case for size. Threaded M3 inserts that will be glued into holes in the sides of the acrylic pieces. Tiny Silverstone NT07-115X Cooler. Slightly louder than Intel Stock cooler. With EQUAL performance and almost half the height. I am touching the plastic backplate. I use anti-static gear CoolerMaster XtraFlo Slim 120mm PWM fan. Extremely quiet and high airflow in a thin package helps make this build possible. Current status: PROJECT COMPLETED! Page 5 has final pics. :3
#beastMODE How powerful can you truly design an SFF? Parts List: [âœ“] Case: Cooler Master Elite 130 [âœ“] Motherboard: Asus ROG Maximus VI Impact[/url] [âœ“] CPU: Haswell i7 4770K [âœ“] Ram: 8GB [âœ“] GPU: GTX 780ti [âœ“] SSD: Crucial 120gb M.2 NGFF [âœ“] HDD: Western Digital Black 750gb 2.5" 7200rpm [_] HDD: 1TB HDD 2.5" 7200rpm [âœ“] Pump: Swiftech Apogee Drive II [âœ“] Radiator: Alphacool NexXxoS Monsta 120 Radiator [âœ“] Fans: 2x Scythe AP29 GT [âœ“] Reservoir: Bitspower 5.25 Bay Reservoir [_] PSU: Silverstone SX600-G 600W SFX Temperatures: LINK Build Log: LINK