VALKYRIE

Members
  • Content count

    350
  • Joined

  • Last visited

  • Days Won

    12

VALKYRIE last won the day on September 5

VALKYRIE had the most liked content!

Community Reputation

9 Neutral

About VALKYRIE

  • Rank
    MasterKeys Clacker

Profile Information

  • Gender
    Male
  • Location
    London UK

Recent Profile Visitors

1,537 profile views
  1. c700p Front Panel

    I agree, I am against closed front panels, but I think is possible to detach and remove the front panel of the C700P
  2. how to install multiple case fan??

    Hi, the abilities of the airflow to cool down the components inside the PC case depends on two airflow properties which are: the speed of the airflow and the temperature of the airflow. If you have no idea how to properly and efficiently develop airflow inside your PC case, then you can install fans everywhere inside your case, install fans on the front, back, top, bottom and also on the left and right side panels. This way you can develop random airflow moving in a variety of directions inside your case at lower speed. Another method which I prefer is to try to allow All the intake airflow to come inside the case (with the help of fans) through a single intake and allow to escape or exhaust outside the case in the opposite side of this intake in a straight line (without 90 degrees deviations), this method offer the advantage of reduced amount of fans and the ability to control at will the specific single airflow speed inside the case, below I add the photo as example and a website link with more detailed explanation about this subject .....http://www.arx-group.com/airflow1.html
  3. Centurion CM590. Fully Ascendant Airflow

    Hi, today arrived here the large cheap 2mm thick thermal pads to install in between the large heat-sink and the case, now I need to cut to size, below some photos, thanks for watching,
  4. Centurion CM590. Fully Ascendant Airflow

    Hi, so far one way I was thinking to transfer some heat from the motherboard to the large heat sink is by using a flat copper sheet (0.5mm thick) from below the motherboard and reaching the underside of the large heat-sink, obviously I need to be very carefully to avoid the underside of the mobo to touch such copper sheet, I dont know how much heat will be able to move towards the heat-sink, but I need carefully to try. Another way to transfer the heat can be by connecting such copper sheet directly from the CPU and after some bending reach the underside of the large heatsink, below some photos of the first idea, thanks for watching
  5. Cooler Master T4

    A while ago I chopped the alleged heat-pipes of a Thermaltake CPU cooler and later also I chopped the heat-pipes of a Thermalright VGA cooler, both were completely Dry inside, the CPU cooler manufacturers use hollow pipes to reduce cost (less copper), reduce weight and because is much much easier to bend hollow pipes instead solid copper rods which are much harder to bend, I plan to chop the end of the heat-piped of one of my CPU coolers which I have two identical here at home to allow some fresh air continuously penetrate the pipes, later I can easy compare the results of both identical coolers. In the link provided below also other people have chopped the pipes of their coolers to find completely dry, no evidence of any liquid......https://forums.anandtech.com/threads/dumb-yet-technical-question-heatpipes.2217753/page-3
  6. new cooler for GX 750w

    If the power supply release smoke, you need RMA and send back where you bought it or may be send to Coolermaster
  7. Centurion CM590. Fully Ascendant Airflow

    Hi, I am going to try to connect this large heat sink 22x146x600mm (which is attached to the case using a thermal pad) to the motherboard or direct to the processor using a flat copper sheet, as a mean to connect both and transfer some heat, obviously if connected to the motherboard I need to be very careful to avoid short circuit to ground, below some photos. I dont know and also I am not sure how much heat I will be able to transfer to this large heat sink using this method, but is just a matter to try and test the results, thanks for watching
  8. Centurion CM590. Fully Ascendant Airflow

    Thanks
  9. Centurion CM590. Fully Ascendant Airflow

    Hi, the newest brackets are ready punched on 2mm hard stainless steel, new hopefully this weekend I can drill holes for the new brackets on the upgraded bigger heatsinks, thanks for watching
  10. How to combine 2 rails of +12V port?

    Perhaps the separate rails are made in purpose to limit (over current protection) the current (Amps) which go through the wires, check the link ....http://www.overclock.net/t/1485311/can-i-bridge-or-combine-12v-rails-in-an-antec-500w-power-supply
  11. Elite 110 and Zotac Gtx 1060 AMP

    GALAX GeForce® GTX 1060 http://www.galax.com/en/graphics-card/10-series/galax-geforce-gtx-1060-goc-3gb.html Dimensions(with Bracket) 195*130*41.5mm
  12. Velocidad de ventilador

    No entiendo la pregunta o cual es el problema, si es que el ventilador hace mucho ruido porque llega a maxima velocidad debido al procesador que se te calienta mucho, tal vez si tienes dinero disponible, podrias cambiar el enfriador tx3i con uno mas grande con ventiladoir de 120 o 140mm
  13. Centurion CM590. Fully Ascendant Airflow

    Hi, I test this modified CPU cooler in a sort of open test bench outside the case, adding the Scythe Mugen 3 attached to the CPU back plate and with with a 2mm thermal blue pad in between, so far the results are not quite special, room temperature about 26 degrees Celsius, and the CPU was reaching 40 degrees at idle even with such extra CPU cooler attached to the back plate. The next step I plan to increase a bit the cooling performance is to increase the size of the extra heat sink at the base of the front CPU cooler from 100x40x20mm to 100x60x25mm, below are shown some photos, thanks for watching
  14. Centurion CM590. Fully Ascendant Airflow

    Hi, today I attached together the CPU cooler with the new CPU heat sink bracket, later I install in the motherboard, thanks for watching
  15. Centurion CM590. Fully Ascendant Airflow

    Hi, this weekend I drilled and tap the holes to attach the brackets for the CPU secondary heat sink, may be I overkill using four screws for each bracket, some photos below, thanks for watching