Christian Dela Rosa

Members
  • Content count

    45
  • Joined

  • Last visited

  • Days Won

    1

Christian Dela Rosa last won the day on March 30 2016

Christian Dela Rosa had the most liked content!

Community Reputation

2 Neutral

About Christian Dela Rosa

  • Rank
    Member

Profile Information

  • Gender
    Male
  • Location
    Smog Hell, CA

Recent Profile Visitors

135 profile views
  1. Hyper 212 EVO Noise

    Most likely defective fan - file an RMA request.
  2. cooler master v8 gts

    Truth spoken, babyzack - slap that cooler on there!
  3. Connecting jetflo 120 to transformer

    You need to identify the +12V and ground leads and attached accordingly to the transformer. The other two wires are speed sensing and PWM control and don't need to be used. Look up "PWM fan pinout" on Google to help you pick out which wires you need.
  4. treesaredancing - please do post what their findings are. I'm very curious - thanks!
  5. Does the Hyper 212 EVO still have intel 775 mountings?

    It looks like the Product Data Sheets still show Socket 775 support, but I would have CM Support confirm.
  6. Variable pump speed? Seidon 120v v2

    Agree with above here. Seidon should be silent and running full speed. That said, I wouldn't expect any issues dropping the speed to 75%, especially if the noise goes away. That would suggest that whatever flow restriction, pump mechanical characteristic, etc. is less prevalent at that speed so it may be beneficial to run it at 75%. However, these units should be quiet. Can you quantify and characterize the noise? Louder than your fans, bubbling, squealing , etc.? Ask the folks where you brought it whether THEY think the noise at 100% is "normal" (seems they avoid the question and say "temps are fine").
  7. Thanks - things just aren't making sense here. The installation should have been very straightforward with the TX3. You verified proper heatsink contact and fan operation when turning on the PC for the first time with the TX3 mounted, correct? Are you overclocked at all?
  8. Is your old fan the stock cooler?
  9. You wonder if too high temps were the case? Have you checked temps on the BIOS screen when you first turned it on?
  10. Seidon 120v - Strange Noise

    It's hard to tell on the video, but have you ruled out each of the fans? That doesn't sound like flow noise. When the sound is occurring, try briefly stopping each of the fans and see if it goes away. If it is the water flow/pump - you've got some good magic going on there.
  11. Nepton 240M and non-K 4790 = temp check

    Those are similar temps I have on a i7 2600 on a Seidon 240M. While there are many other factors which determine when a loaded CPU's thermal solution settles at, being at similar TDPs - you are probably on the good side.
  12. Cooler Master Cosmos II for Supermicro X10DRG-Q

    Form factor is labeled "Proprietary" on SM's website. Chances for fit don't look too good...
  13. Seidon 120V CPU Temp Overheat

    It also sounds like if you're immediately getting the temp overheat shutdown right after turning it on - it's a sensor or BIOS issue. You should have some time to at least enter the BIOS screen while the CPU heats up. I recall inadvertently powering up an old AMD Athlon chip without a heatsink while the motherboard was on an open test bed and I know took at least a minute for the BIOS to register something was wrong. Do you have a easy to install stock cooler available? You can mount that temporarily onto the CPU (without paste even) and see if you can get into the BIOS screen - go to Computer Health and see what registers. If you can't get past powering on the motherboard - issue is most likely the mobo or sensor. Have you reset the CMOS?
  14. Cool Master 430 elite Mess up Power wires?

    I'd test the PSU first before hooking it back up to the mobo. Do you have a "known good" spare PSU you could test the motherboard further on?
  15. Ambient Air Chilling prior to case intake

    I have heard of Peltier coolers integrated into CPU cooling solutions, but not an "add-on" device to connect up to the intake air. I'm sure it'll work - maybe it'll be more economical? As this is "off-topic", have you checked other forums to broaden the audience of this question (ATOT, HWS, etc.)?