• Content count

  • Joined

  • Last visited

Community Reputation

1 Neutral

About snapper69

  • Rank
  • Birthday September 28

Profile Information

  • Gender
  • Location
  1. snapper69

    I need some help replacing a CPU fan?

    Have you tried contacting Best Buys? It should still be under Guarantee, so if there's a problem, it's their responsibility.
  2. snapper69

    Pump Noise with the Seidon 120M

    This type of noise can often be caused by air bubbles in the pump, one possible cure is to lie your case on it's side for a few hours/overnight with the pump running.
  3. snapper69

    Newbie to building a pc and figuring out the specs

    Checking the spec for your case indicates that it will take a cooler up to 185mm high. The spec for the hyper 212 evo lists it as being 120 x80x159 mm, so it should easily fit, with room to spare.
  4. snapper69

    Silencio FP 120 PWM Performance Edition

    Try this link or this one
  5. The sound glitch is a problem with Fallout 4. My 240M pump is quiet enough that my ears can't hear it and the fans (controlled by Asus software) are quiet enough for me, either on silent or balanced (mostly silent). I previously used a Corsair Commander Mini and Link software to control the fans, but as my new Asus Hero VIII has more than enough fan headers, I'm now using the Asus software to do the job. To be honest, I'm so addicted to Fallout 4 that I haven't really had time to "mess about" with my settings, however, sooner or later it will happen and I'll let you know what happens. Yesterday I had to reboot my computer and the temp shot up to 88 degrees and the fan speed ramped up ( on a positive note, at least I now know that the fans work as they should ), I checked as many settings as I could, before rebooting it again. It came back to normal, weird. Anyone else had this happen?
  6. Very nice, playing Fallout 4 at 4k with no problems, apart from an occasional sound glitch. I've overclocked it to 3.9 and it's rock solid. The next time that I switch it off, I'll try for 4.5 ish. The 240M does a good job of keeping it cool too, high 20's on idle and low 40's sfter a couple of hours of gaming.
  7. Thanks for that, it was useful, but on the Corsair forum there have been several instances where the back plate has been loose (due to the Asus board being thinner), causing the pump to make poor contact with the cpu and the temps to be high. The cure for that seems to be mounting the back plate with rubber washers. I was wondering if anyone has had a similar problem mounting the 240M onto an Asus board, or if the Cooler Master mounts somehow compensate for this problem? Update. It appears that, unlike some coolers, there isn't a problem. I installed everything on New Years Day and it works perfectly.
  8. I am about to upgrade my system to Skylake, using an Asus Maximus Hero VIII motherboard and I have read on certain sites/forums that the slightly thinner Asus motherboards cause problems mounting AIO coolers such as the 240M, some people finding it necessary to use rubber washers. I was wondering if anyone on here had encountered any problems?
  9. snapper69

    Fans not running on Nepton 240m

    It sounds to me as though you aren't getting enough juice to your fans, try disconnecting one of them and see if the other runs. Most fan controllers that I've seen, require their own power supply, usually from a Sata or Molex connector.
  10. My understanding is that you connect the pump to the cpu_fan header and the fans to the sys_fan header, at least that's how I've always done it. On most motherboards you need something working on the cpu_fan header in order for it to boot, so if your pump stops working it will warn you.
  11. "Any reason for why this would happen and should I be worried?" No it shouldn't happen and you should be worried about where all that coolant went. Water and electricity/circuit boards don't play well together. I have been using AIO water cooling for 10+ years and I have only had 1 leak, from an early model cooler that had been installed and uninstalled several times and it took my graphics card and motherboard with it.
  12. snapper69

    Nepton 240m sounds like a cheap aquarium

    Try putting your finger on the top of the pump and GENTLY pressing down to see if the noise stops. My rule of thumb for installation is to tighten the screws by hand as much as I can and then give them 1/4 to 1/2 of a turn with a screwdriver. It works for me, but then I'm in my 60's and my grip isn't what it used to be.
  13. snapper69

    Fan setup for HAF XB EVO with NO water cooling.

    I would try to aim for a balanced or slightly positive pressure system, that way dust will not be drawn into your case through every available orifice. You could try: 1) 2 x 120 mm fans at the front as intakes, 1 x 120 mm fan at the rear as exhaust and cover the top. 2) 2 x 120 mm fans at the front as intakes, 1 200mm fan on top, no fan in rear. 3) as 2) but with the rear fan as an intake (filtered of course).
  14. snapper69

    Push Pull -Nepton 240M

    What about the rubber gasket that comes with the Nepton 240M? Is that available?
  15. snapper69

    Nepton 240m Pump Rattle/Noise/Ticking

    Amazon do, I had a Corsair H100i (actually I had 3 of them) and the first twice they sent me a new one out and gave me 30 days to return the faulty one. On the third occasion, they gave me a refund. I'm told that Corsair will also do an advanced RMA, where they send you a replacement before you return the old unit, however I believe that you need to give them a valid card number, in case you don't return the old unit. I switched to the Nepton 240M because of the problems that I had with those H100i's and the fact that my H110i GT wouldn't fit in my new case.