Leaderboard


Popular Content

Showing content with the highest reputation on 05/19/2017 in all areas

  1. 1 point
    PROJECT PV2 by Paulo Reis Aka EVILPT WORKLOG About Myself First of all I will introduce myself my name is Paul I'm 36years old and live in Portugal "Sintra" I am computer technician and as was expected love modding. I hope you enjoy the PROJECT PIPELINE V2 "PV2" Design Concept The project PV2 After several incentives and support I was led to do Version 2.0 of the Pipeline Project. Then the whole project goes back from the crystalline and open structure with an EL 110v cable lighting and a giant watercooling system made by me with full support from Alphacool. The water besides walking through the conventional tubes still walks inside the 32mm acrylic structure of the PV2. I always found this type of structure fascinate and different I hope you like it as much as I liked doing this project. Best Regards and good luck too all. Portugal Mod Squad. Tks To All.. Sponsors Very Happy to Announce my Sponsors COOLER MASTER PORTUGAL TKS Sofia!! ALPHACOOL - AQUATUNING.DE TKS EDDY!! AVEXIR TKS Peggy!! AND ALL AVEXIR TEAM Materials to be used in the design of this Project PV2 Material to be used in the design of this Project Acrylic Ex Cristal Tube 32mm Acrylic water tube 16mm ALPHACOOL Fittings 16mm ALPHACOOL Reservoirs 250mm with Pump DC5 ALPHACOOL Sleeving Cable By Paulo Reis and PHOBYA 6 Fan Connector PHOBYA PVC Water tube 32mm Grill Mesh Spray "Black Mate" Spray "Black Textured" EL Wire LED Strip Aluminum Tube 10mm *Silicon tube 3mm and 4mm Wire 0.22 Soldering iron Station by VELLEMAN Hardware Motherboard: MSI Board "NOT Sponsor" Avexir DDR4: 16GB Quadchannel Blue Led Raiden Effect Avexir SSD S100 Blue Effect CMaster: JetFlows 120 Blue CMaster: Power supply V650 M GPU: ATI HD7870XT Watercooled CPU Intel 1151: I7 6700k LET´S START WORKLOG PHOTOS p FINAL PHOTO PROJECT PV2 BY PAULO REIS AKA EVILPT VIDEO OF THE PROJECT PV2 "ON" PV2 Video HOPE YOU LIKE THE PROJECT TKS TO ALL SPONSORS, FRIENDS AND MY FAMILY FACEBOOK: https://www.facebook.com/PauloReisakaEvilPT INSTAGRAM: https://www.instagram.com/evilpt/ TWITTER: https://twitter.com/evil_pt
  2. 1 point
    The results are published, our project were left unnoticed. Thanks to sponsors on their trust and all of you for the enormous support! http://community.coolermaster.com/topic/22290-case-mod-world-series-2017-winners-revealed/
  3. 1 point
    Hello Everyone.. I'm Raka from Indonesia --------------- WELCOME AND THANKYOU FOR FOLLOW MY WORKLOG ------------------- --- The Legend Series Of Cooler Master Case with Mid Specification --- This is my personal computer, I want to make this chassis look more attractive. Because I think the coolermaster stacker case is suitable for modification and has a sturdy design of thick aluminum material. The Red Hat project that I made will change the concept of the casing type with the old model to be a newer model. I will change it slightly to the casing with acrylic. The front of the casing for airflow, then to the left and right sidepanel we replace it with a piece of acrylic with wing style to open it like a supercar with the help of hydrolics system. Some panels and pillars that I will cut to facilitate the management of the cable, so the cable cable will be easily installed on the back or side of the motherboard. Some also we will install assesories such as fans, led, etc. For outdoor display we will make by playing window film, cutting sticker, and knick-knacks as a complement. I still can not tell you all the details but I will continue to display any process into my worklog. And you will be able to enjoy all the stages of the process. We look forward to any feedback or comment to Red Hat if it is unacceptable and please note due to the lack of preparation and limitations in this series of Case Mod events. Thank's Cooler Master Specifications My Pc Rig: CPU : Amd Phenom x6 1055T Motherboard : Asus Rog Crosshair IV Formula VGA : Palit Geforce GTX 275 series RAM : Corsair Vengeance Pro Series 16GB SSD : Pioneer SSD 120 Gb Case : CoolerMaster CM Stacker Black PSU : Corsair Hx1000 Watt. Cooling : Cooler Master X6 Fan : Enermax Tb Appolish 12cm 1pcs, Da Orkaan 12cm 4pcs, Cooler master 12cm 1pcs, Thermaltake 8cm 1pcs, Corsair Ram cooler 1pcs Cable sleeving : Mod custom Hidrolic : Pneumatic 100N ------------------------------------------- WELCOME AND THANKYOU FOR FOLLOW MY WORKLOG --------------------------------------- Prepare for Toolkits first.. Pray before work.. and use the tool as its function and safety as a primary! Keep on it.. Thankyou.. ******** Progressive Progress results ********* The Red Hat [Hidraulic's System] **Before **After
  4. 1 point
    VIDEOS HOPE YOU LIKE THE PROJECT TKS TO ALL SPONSORS, FRIENDS AND MY FAMILY FACEBOOK: https://www.facebook.com/PauloReisakaEvilPT INSTAGRAM: https://www.instagram.com/evilpt/ TWITTER: https://twitter.com/evil_pt
  5. 1 point
    Hy friend's ,, i will unpack psu .. because psu long enough i wear and have aged .. so maybe a lot of dust there .. lol .. let's check .. Before I will close the corsair sticker with clear tape, so that later when I paint easy to remove it ,, and easy to find the curve part so that I can easily cut in accordance with the pattern Then I continue the work of unpacking the psu cover first with a screwdriver plus rusty and dusty everywhere.. Hahaha.... but it's working next, I took off the part I could take off After removing the cover, fan and others .. I will cover certain parts to avoid paint during painting process Next..
  6. 1 point
    Helloo everybody,, Thankyouu keep stay on my worklog.. Here I have prepared acrylic at the beginning of the worklog, the part I want to do now is the side casing .. I will do the initial drilling, for the rotary hinge section using axles and bearings. Which then I deepened again about 2mm, So that the surface is flattened with the other parts After finishing the holder for the hydraulics, I made the installation of a rotary hinge for the hydraulic end of the swing and do not forget also to make persing to head bolt to surface flat with acrilic I will try to install the hydraulic with the bearing holder that I made earlier,, try it first with plywood .. I am afraid of wrong and choose to be careful, although I have measured and I make sure it. And also I do a test whether hydrolic can work as I expected or not. Next......
  7. 1 point
    I try to remove every part of the side casing Removing the hook by bending the plate net using pliers Done!! Plate nets and side casing are released I will make a holder for hinges, bearings, and bolts so that later side panel casing and hydrolic suspension can be installed correctly.. Then I cut acrylic with a thickness of 5mm and I made the double to its thickness to 1cm. I do the gluing using acrylic glue. This thing i need to make side casing more out of case. The next stage I make a hole for bolt holder and hydraulic holder Specifically for my axles make depth with different drill techniques Next step ,, i am looking for bearing in auto shop with small diameter size. Which I then got with the size of 14mm diameter Next Worklog... Thankyou for Following...
  8. 1 point
    Quick update with some sketches that I've been working on for the past few days. I've eyeballed most of the measurements, some adjustments may be necessary. The first attachment shows the external, left-hand side of the build. I'll be fabricating this from aluminium composite materials (3rd pic) tomorrow. It's usually a bad ideea to build this from the outside in, but hey that's what sketches are for. Queue some hardcore dremel action. Second attachment is a rockin' pulley transmission system. Bit of a headache to design, but just wait and see it in action! None of the components, that I ordered, have made it through shipping yet, so it's all fabricobbling until the easter bunny hops around.
  9. 1 point
  10. 1 point
    Welcome back, This progress while we make. stage-by-stage we've done. back I have to prepare materials that will we will raft for modding purposes. before we will test whether all the hardware working properly or not after the work is completed stacker chassis. back baffled .. must choose between seidon 120 or Cooler Master X6 would use .. Sata cable specials from cooler master .. MOD X Fan Display also will I use to accent I prepare a wide variety of LED light sticks and strips to create color variations. Controller fan and LED assemblies to facilitate the installation of LED lights, and others So long time to be dry.. and im still waiting for the paint drying process ... Motherboard cover design Vynil Carbon for main frame.. its purely carbon fibre looks.. Vga GeForce GTX 275x mine is not good looks. and I will make it okay .. including making backpanel vga and others make it look more presentable Upss... And this is a temporary display as far as I make to this day. Wait for the next edition as whether the rig pc that I wear and what I later modding .. we wait for the next post .. see you later. Thankyou for review.. guys..
  11. 1 point
    Kamsiaaaa Om Ad Jago.. thx master..
  12. 1 point
    Maybe something like this.. source : https://www.google.co.id/search?q=supercars+doors&espv=2&tbm=isch&tbo=u&source=univ&sa=X&ved=0ahUKEwjQ1_6C6YDTAhWGm5QKHf1TArsQsAQIGA&biw=1920&bih=935#imgrc=dfExTVkikvOObM: Well.. Hidraulic Adjustable Stabilizer Kit I have prepared.. I need two pairs to be installed on the right and left of the chassis.. But I still needed something to pair,, attached the end of the casing and the other mounted on the side panel acrylic sheet.. .....thinking.. Next... I tried to measure the hinge and the base so that the stabilizer can move as it should. After searching for an idea I got a lock on the motorcycle accessories store. and this lock can rotate 360 degrees as a hinge. I try to install the stabilizer acrylic and the casing holder for retaining stabilizer we have designed .. And back I created a hinge for the side acrylic. Thankyou for follow and see my worklog.. wait for the next update guys...
  13. 1 point
    Now I will make mounting bolts for each of each body acrylic, and make it become increasingly clear picture One Hole One Bolt... Drill... Drill... and Drilll again.... [Drill the Acrylic one] Drill the Main Case.. Next Step....
  14. 1 point
    The next step....... I release the locking plastic parts, aluminum and other supporting components that are not on the main part of the casing. Due to not hit the paint later time I will do the painting chassis. Then I measure and make powersuply cable lines. I will make the SSD or hard drive on the right motherboard. and then I will make a hole for easy sata cable and power in the arrangement
  15. 1 point
    This post was initially reserved for the final submission shots, that time has now come. I give you MKTRX Ammo 315, the ultimate lan-party rig: